Baxi 130 he installation manual

Smoke Products. System Protection. Test Equipment. Filter by type. Filter by category. Filter by brand. Andrews Water Heaters. Boulter Buderus. British Gas. Ferroli Boiler Spares. Glowworm Boiler Spares. Halstead Heating Boiler Parts. Hamworthy Boiler Spares. Heatline Boiler Parts. Ideal Commercial Boiler Spares. Ideal Domestic Boiler Spares. Ikon Boiler Parts. Intergas Heating Parts. Jaguar Boiler Parts. Keston Boiler Spares. Main Spare Parts. Malvern Boiler Spares. Myson Boiler Spares.

Potterton Boiler Spares. Ravenheat Boiler Spares. Remeha Heating Spares. Saunier Duval. Scottish Gas Boiler Spares. Servowarm Boiler Spares. Sime Boiler Parts. Vaillant Boiler Spares. Viessmann Boiler Spares. Vokera Boiler Spares. Filter by appliance. HE COMBI e At a flow rate of approximately 4. The test data from Page 8: Dimensions And Fixings 5. Page Pressure Relief Valve Check 3. For optimum operating conditions and maximum Valve Valve Valve economy the fitting of the Baxi Intellistat, is recommended.

System Filling and Pressurising 1. A filling point connection on the central heating Temporary return pipework must be provided to facilitate initial Page 11 6. All DHW circuits, connections, fittings, etc.

Boiler should be fully in accordance with relevant Expansion standards and water supply regulations. Vessel 2. Page Site Requirements 7. Page 13 7. If the boiler is fitted in a room containing a bath or shower reference must be made to the relevant requirements.

In GB this is the current I. Page 14 7. Page 15 7. The standard horizontal flue kit allows for flue lengths between mm and mm from elbow to terminal Fig. The maximum permissible equivalent flue length is: 4 metres horizontal Fig. Page 16 Installation Guidance Notes for each flue system type. Documents and for concentric and twin pipe respectively. Page Installation It must be fitted in parallel to the existing pump and in the return pipe. Page 18 Fig. Baxi declare that no substances harmful to health are contained in the appliance or used during construction of the appliance.

Service Guidance Note Label on inside of panel Fig. Page 19 Gas connection first to centralise the boiler. The gas sealing washer is an integral part of the gas tap. The Combi HE is designed to operate under nominal water supply conditions. If the Tap Rail Facia Securing Page 20 Wall Thickness 8. Page 21 If necessary fit a terminal guard see Gasket Section 7. For information on vertical flues consult the Fig. Page 22 8. The electrical connection is on the rear left hand side of the unit.

Metal Shield Plug 2. Remove the electrical plug from the hardware pack. Filter 3. Refer to the Baxi Intellistat instructions. The boiler installation parameters must be set Filter Optional Live Feed For up to recognise that the Intellistat will operate in An External Pump conjunction with the boiler see section Page 25 9.

Open the cold feed to the boiler. Page 27 The boiler will automatically vary its output to match the system load giving the most efficient use of gas and the most comfortable room temperature possible. Page 28 Page 29 For optimum efficiency, this boiler can be controlled by an optional control accessary, the Baxi Intellistat Part No. Page Fitting The Outer Case Fit the outercase to the appliance ensuring that the four slots in the side flanges align with the hooks on the chassis Fig.

Insert the two fixing screws into the sides of the chassis Fig. Page Servicing The Boiler Also for safety, unplug the boiler at the electrical inlet socket. Hazardous materials are not used in the construction of Baxi products, however reasonable care during service is recommended. For reasons of safety and economy, it is Air Box Door Panel recommended that the boiler is serviced annually.

Page Site Requirements 7. The boiler may be fitted to any suitable non- flammable wall with the flue passing through an outside wall or roof and discharging to atmosphere in a position permitting satisfactory removal of combustion products and providing an adequate air supply. Page 14 7. A flat vertical area is required for the installation of the boiler.

These dimensions include the necessary clearances around the boiler for case removal, spanner access and air movement. Page 15 7. Page 16 7. Page 17 7. The standard horizontal flue kit allows for flue lengths between mm and mm from elbow to terminal Fig.

The maximum permissible equivalent flue length is: 4 metres horizontal Fig. Page 18 Installation Guidance Notes for each flue system type. Documents and for concentric and twin pipe respectively. Page Installation It must be fitted in parallel to the existing pump and in the return pipe. Page 20 Fig. Baxi declare that no substances harmful to health are contained in the appliance or used during construction of the appliance.

Service Guidance Note Label on inside of panel Fig. Page 21 Gas connection first to centralise the boiler. The gas sealing washer is an integral part of the gas tap. The Combi HE is designed to operate under nominal water supply conditions.

If the Facia Securing Tap Rail Page 22 Wall Thickness 8. Page 23 If necessary fit a terminal guard see Gasket Section 7. For information on vertical flues consult the Fig. Page 24 8.

A plug is supplied with the boiler and the electrical connection is at the rear left hand side Metal Shield of the unit. Plug 2. Remove the electrical plug from the kit pack. Filter 3. Page 25 8. Refer to the Baxi Intellistat instructions. The boiler installation parameters must be set to Filter Optional Live Feed For recognise that the Intellistat will operate in An External Pump conjunction with the boiler see section Page 27 9.

Open the cold feed to the boiler. Page 29 The boiler will automatically vary its output to match the system load giving the most efficient use of gas and the most comfortable room temperature possible.

Page 30 Page 31 Switching on the Intellistat Fig. Page Fitting The Outer Case Fit the outercase to the appliance ensuring that the four slots in the side flanges align with the hooks on the chassis Fig. Insert the two fixing screws into the sides of the chassis Fig. Page Servicing The Boiler Hazardous materials are not used in the construction of Baxi products, however reasonable care during service is recommended. For reasons of safety and economy, it is recommended that the boiler is serviced annually.

Page 34 Burner To clean the heat exchanger and burner proceed as follows: a Disconnect the electrical leads to the fan component protection sensor Fig. Page Changing Components Hazardous materials are not used in the Heat Exchanger construction of Baxi products, however Manifold reasonable care during service is recommended. Page 36 Drain the boiler see Section It may be necessary to remove the expansion vessel see Section