2008 server pptp setup

Cause : The VPN client and the VPN server in conjunction with a remote access policy aren't configured to use at least one common authentication method. Solution : Configure the VPN client and the VPN server in conjunction with a remote access policy to use at least one common authentication method. For more information about how to configure authentication, see the Windows Server Help and Support Center. Cause : The VPN client and the VPN server in conjunction with a remote access policy aren't configured to use at least one common encryption method.

Solution : Configure the VPN client and the VPN server in conjunction with a remote access policy to use at least one common encryption method.

For more information about how to configure encryption, see the Windows Server Help and Support Center. Cause : The VPN connection doesn't have the appropriate permissions through dial-in properties of the user account and remote access policies.

Solution : Verify that the VPN connection has the appropriate permissions through dial-in properties of the user account and remote access policies. For the connection to be established, the settings of the connection attempt must:. For more information about an introduction to remote access policies, and how to accept a connection attempt, see the Windows Server Help and Support Center.

Cause : The settings of the remote access policy profile are in conflict with properties of the VPN server. The properties of the remote access policy profile and the properties of the VPN server both contain settings for:.

If the settings of the profile of the matching remote access policy are in conflict with the settings of the VPN server, the connection attempt is rejected. Solution : Verify that the settings of the remote access policy profile aren't in conflict with properties of the VPN server. Cause : The answering router can't validate the credentials of the calling router user name, password, and domain name.

Solution : Verify that the credentials of the VPN client user name, password, and domain name are correct and can be validated by the VPN server. Solution : If the VPN server is configured with a static IP address pool, verify that there are enough addresses in the pool. If all of the addresses in the static pool have been allocated to connected VPN clients, the VPN server can't allocate an IP address, and the connection attempt is rejected.

If all of the addresses in the static pool have been allocated, modify the pool. Solution : Verify the configuration of the authentication provider.

Solution : For a VPN server that is a member server in a mixed-mode or native-mode Windows Server domain that is configured for Windows Server authentication, verify that:.

If not, create the group and set the group type to Security and the group scope to Domain local. You can use the netsh ras show registeredserver command to view the current registration. You can use the netsh ras add registeredserver command to register the server in a specified domain.

To immediately effect this change, restart the VPN server computer. For more information about how to add a group, how to verify permissions for the RAS and IAS security group, and about netsh commands for remote access, see the Windows Server Help and Support Center.

If not, type the following command at a command prompt on a domain controller computer, and then restart the domain controller computer:. For more information about Windows NT 4. For more information about how to add a packet filter, see the Windows Server Help and Support Center. Cause : The appropriate demand-dial interface hasn't been added to the protocol being routed.

Been sometime since I set this up. Hi, I tried to accomplish this setup and it worked perfectly when I use windows connection, but when I use a hardware to hook it is not established. How can we setup vpn on server running only sql server, no ad or domain?

Trackbacks […] this article for the benefit of all netizens. Leave a Reply Cancel reply Your email address will not be published. Enter your server address. Select the type of trusted VPN connection. Set these credentials. So we have to add our role. Right-click on the server name and select Configure and enable routing and therefore remote access.

You will see that all server state changes become active green icon with an arrow pointing up. Right-click and selectSelect Properties. Select Allow connections. Click OK. I have Linux Shorewall firewall. I am watching a live debug document while connecting remotely to an RRAS host. Step 1: Update the system. Step 2: Install the remote access role. Step 3: Set up routing and remote access. Asked 6 years, 5 months ago. Active 6 years, 1 month ago. Viewed 47k times.

Improve this question. Pro Backup Pro Backup 4 4 gold badges 15 15 silver badges 33 33 bronze badges. Add a comment. Active Oldest Votes. Expand your server , and then expand ports.

Open the properties of your server via the server its context menu right clicking on your server name. Then open tab security.